This page was exported from Free Braindump2go Dumps (VCE & PDF) - 100% Valid! [ http://www.vcesplus.com ] Export date:Wed Dec 11 23:08:31 2019 / +0000 GMT ___________________________________________________ Title: Jan/2019 300-180 Dumps-VCE and PDF(Full Version)1416Q Download in Braindump2go[Q161-Q171] --------------------------------------------------- January/2019 Braindump2go 300-180 Exam Dumps with PDF and VCE New Updated Today! Following are some new 300-180 Real Exam Questions:1.|2019 Latest 300-180 Exam Dumps (PDF & VCE) 416Q&As Download:https://www.braindump2go.com/300-180.html2.|2019 Latest 300-180 Exam Questions & Answers Download:https://drive.google.com/drive/folders/0B75b5xYLjSSNRFptN0xiTENBMzA?usp=sharingQUESTION 161After you hot swap an HDD, the updated HDD metrics fail to appear in the Cisco UCS Manager GUI. Which option is the most likely cause of the problem?A. The Cisco UCS Manager gathers hard disk metrics only during a system boot.B. The hard disk firmware version is unsupported.C. The hard disk failed to initialize.D. The hard disk is a member of a RAID-1 array.Answer: AQUESTION 162You have a Cisco UCS Fabric Interconnect in Fibre Channel end-host mode. You must check whether all of the Fibre Channel targets are available through the fabric interconnect at VSAN 200. Which command must you use?A. show npvflogi-tableB. show flogi-tableC. show flogi databaseD. show zoneset active VSAN 200Answer: AQUESTION 163Which names are reserved when custom roles are created in Cisco UCS Manager RBAC?A. network-admin, network-operator, vdc-admin, vdc-operator, and server-adminB. cisco, cisco123, cisco-operator, cisco-admin, and rootC. ucs-admin, ucs-operator, server-admin, server-operator, and cisco-adminD. ucs, ucs123, server-admin, server-operator, and sysrootAnswer: AQUESTION 164A customer starts an Auto Install upgrade process. During the process, the customer selects the wrong firmware version. Which action rolls back to the previous firmware version as quickly as possible?A. Cancel the process by using the Cisco UCS Manager.B. Wait for the upgrade to complete, and then roll back the configuration.C. Wait for the upgrade to complete, and then downgrade.D. Cancel the process by using the CLI.Answer: CQUESTION 165You must check the path that vNICs uses to communicate. How can you verify whether a vNIC on a Cisco UCS server is in an active state or a failover state?A. Run the show interface brief command.B. Connect to the adapter and execute the Master Control Program.C. Compare the state on both fabric interconnects.D. Run the show interface status command.Answer: CQUESTION 166Which option describes how you can reset the BIOS password of a Cisco UCS C-Series Rack-Mount Server?A. Turn off the server. Press and hold the F7 key, and then turn on the server.B. Reset the jumper on the motherboard.C. Press and hold the power switch for 20 seconds.D. Turn off the server. Press and hold the F2 key, and then turn on the server.Answer: BQUESTION 167You upgrade an operating system on a Cisco UCS C-Series Rack Server. After the upgrade, you discover that the performance of the server is much slower than expected. You verify that the operating system is on the Cisco support matrix for the rack server. Which two firmware types are the possible cause of the performance issue? (Choose two.)A. fNICB. eNICC. mptspiD. vNICE. vSwitchAnswer: ABQUESTION 168You have an unresponsive blade server. You suspect that there is an issue with the current firmware. Which action do you take to reboot the server from the Cisco UCS Manager GUI?A. Reset the server.B. Reset CIMC.C. Reset BMC.D. Recover the corrupt BIOS.Answer: BQUESTION 169How many FSM tasks can run concurrently on a server?A. 1B. 2C. 4D. 16Answer: AQUESTION 170You have remote CLI access using SSH to the Cisco UCS equipement of a customer. Which command must you use to check for system errors in the UCS domain?A. show faultB. show clusterC. show chassisD. show failoverAnswer: AQUESTION 171You are troubleshooting a remote Cisco UCS environment that has Cisco UCS 2208 I/O Modules. Some of the links from the IOMs to the UCS Fabric Interconnect fail to work as expected. You check whether the SFP is in place and the state of the IOM ports. Which command do you use to view the MAC and PHY status to determine whether the SFP is detected in the IOM?A. show platform software redwood operB. show platform software woodsideoperC. show platform software woodsidestsD. show platform software redwood postAnswer: B!!!RECOMMEND!!!1.|2019 Latest 300-180 Exam Dumps (PDF & VCE) 416Q&As Download:https://www.braindump2go.com/300-180.html2.|2019 Latest 300-180 Study Guide Video: YouTube Video: YouTube.com/watch?v=a5cUmpBk63M --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2019-01-04 02:59:01 Post date GMT: 2019-01-04 02:59:01 Post modified date: 2019-01-04 02:59:01 Post modified date GMT: 2019-01-04 02:59:01 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com